![]() While hiding in a ruined church, the four are again attacked by the Zombie Mecho-Marauder and were saved by survivor Professor Veronica Chase and her colleagues of Empire State University. The four were soon attacked by Earth-2149's Moon Knight, Tigra, and Shamrock, and eliminated them before escaping from more hordes of superhuman zombies. Betty and Bill, who were frightened away by Man-Thing. This time successful, the Deadpools entered Earth-2149 and joined by Dr. ![]() Fortunately, Doctor Voodoo appeared before them and helped them bridging the portal to Earth-2149. The two unsuccessfully returned to Earth-616 where they have only been gone for a few seconds. Though, the two instead entered a few alternate universes where they meet their counterparts. After finding a portal to the Multiverse, the Deadpools entered into it in the hopes of finding Earth-2149. Once in Florida, the four avoided a territorial Man-Thing and fought, and killed Hydra's Lord Falcon. agent named Bill, headed to Florida's swamps where the Zombie Deadpool first appeared on Earth-616, in the hope of returning him back to his home universe. Once again escaping from Hydra when the station came under attack, the two Deadpools along with Dr. ![]() ![]() planned to weaponize traces of the zombie plague from the Zombie Deadpool. However, Deadpool-616 decided to save Zombie Deadpool after carefully learning that A.I.M. Betty escape on one of Hydra's shuttle to A.I.M.'s satellite where the Zombie Deadpool was detained for examination. After escaping the carnage, Deadpool, his living counterpart, and Dr. Zombie Deadpool was randomly possessed by each party during the chaos until being picked up by Deadpool-616. Betty and torturing Deadpool, but was interrupted by a massive battle between the returning Headhunters and a Tyrannosaurus Rex lured by Ka-Zar. Eventually, Hydra discovered the Zombie Deadpool after interrogating Dr. Betty were able to extract Zombie Deadpool from the cave, but were captured by Hydra agents, leaving Zombie Deadpool in the bushes behind them. Zombie Deadpool planned for the removal of this universe's Deadpool's head so that he could use the body. operative, and this universe's Deadpool were sent to retrieve him before Hydra could. Hydra was searching the area for toxins that could be used for weapons when they discovered his presence. after faking his death, and floated into a cave in the Savage Land where he was found by Headhunters and worshipped as a god, since the cave was sacred to them. However, Deadpool soon escaped with the help of Garth after biting one of Black Talon's guard.Įventually Garth sent Deadpool on a raft away from A.R.M.O.R. Black Talon assumed control of Garth, and captured Deadpool's head. Garth was compelled to travel to the island nation of Taíno in the Caribbean Sea, where he told Black Talon about the zombie plague. Headquarters with the help of Simon Garth by using the base's teleporters to escape to the bottom of the sea, where Deadpool's head infected all of the Men-Fish. ĭeadpool, now reduced to only a head, managed to escape from A.R.M.O.R. However, as the "Prime Carrier" he was contained within A.R.M.O.R. He appears to be killed when Wundarr the Aquarian threw him and Kale retaliated by luring Deadpool into the blades of a nearby skiff, completely tearing him apart. He later transported from Earth-2149 to Earth-616, calling himself the "Merc with half a Mouth" (due to his lack of most of his jaw) and exhibiting a wide range of knowledge, which he used to take out Jennifer Kale's magic, and then attacked her. He most likely fled the attack but also escaped the Power Cosmic zombies from getting himself incinerated and killed. Little is detailed about Deadpool’s life before the zombie plague arrived on Earth-2149, however it can be presumed that it followed much the same path as his Earth-616 counterpart.Īt some point he was infected, and attacked the Silver Surfer.
0 Comments
![]() These three planes are marked A, B and C, where A is the face side, B is the first datum edge, and C is the second datum edge. For example, the three planes could be one "face side" and two "datum edges". A typical datum reference frame is made up of three planes. Datum reference frames are used as part of the feature control frame to show where the measurement is taken from. In geometric dimensioning and tolerancing, datum reference frames are typically 3D. These are then referred to by one or more 'datum references' which indicate measurements that should be made with respect to the corresponding datum feature. In engineering and drafting, a datum is a reference point, surface, or axis on an object against which measurements are made. Screenshot from AutoCAD showing usage of T.I.R., perpendicularity, and parallelism GD&T datum reference symbols.Īn engineering datum used in geometric dimensioning and tolerancing is a feature on an object used to create a reference system for measurement. The datum for light airplanes is usually the engine firewall or the tip of the spinner, but in all cases it is a fixed plane perpendicular to the aircraft's longitudinal axis, and specified in its operating handbook. This requires the calculation of moment for each variable mass in the aircraft (fuel, passengers, cargo, etc.), by multiplying its weight by its distance from a datum reference. In aviation, an aircraft is designed to operate within a specified range of weight and (chiefly longitudinal) balance an airman is responsible for determining these factors for each flight under his or her command. In subsequent marking out, all measurements are then taken from either of the two datum references. ![]() ![]() If necessary they may be cut, planed or filed to make them so. For most work, the datum references of the workpiece need to be square. One convention is to mark the first datum edge with a single slanted line (/) and the second with double lines (//). The artisan nominates two straight edges on a workpiece as the "datum edges", and they are marked accordingly. In carpentry, an alternative, more common name is "face side" and "face edge". The concept of datums is used in many fields, including carpentry, metalworking, needlework, geometric dimensioning and tolerancing (GD&T), aviation, surveying, geodesy ( geodetic datums), and others. This matters because the hub and rim need to be concentric to within close limits (or else the wheel will not roll smoothly). ![]() For example, on a car's wheel, the lug nut holes define a bolt circle that is a datum from which the location of the rim can be defined and measured. JSTOR ( November 2015) ( Learn how and when to remove this template message)Ī datum reference or just datum (plural: datums ) is some important part of an object-such as a point, line, plane, hole, set of holes, or pair of surfaces-that serves as a reference in defining the geometry of the object and (often) in measuring aspects of the actual geometry to assess how closely they match with the nominal value, which may be an ideal, standard, average, or desired value.Unsourced material may be challenged and removed. Please help improve this article by adding citations to reliable sources. This article needs additional citations for verification. |